Servomotore Shark-5 (0,70 sec/60°, 14 RPM 2360 oz-in coppia, rotazione 504°)

459,61 (376,73 + IVA)

Available

COD: 3216-0001-0005 Categoria:

Servomotore Shark-5 (0,70 sec/60°, 14 RPM 2360 oz-in coppia, rotazione 504°)

459,61 (376,73 + IVA)

Available

COD: 3216-0001-0005 Categoria:

European Costumers

SPECIFICHE
Peso 224 g
Rapporto di trasmissione 5:1
Intervallo di tensione 6 V – 8,4 V
Velocità a vuoto (6,0 V) 0,85 sec/60° (11,8 giri/min)
Velocità a vuoto (7,4 V) 0,70 sec/60° (14,3 giri/min)
Coppia di stallo (6,0-7,4 V) 2360 oz-in (170 kg.cm)
Corrente a vuoto (6,0 V) 260 mA
Corrente a vuoto (7,4 V) 270 mA
Corrente di stallo (6,0-7,4 V) 2700 mA
Tipo di motore CC senza spazzole
Direzione con aumento del segnale PWM in senso antiorario
Intervallo PWM massimo 800-2200 μsec
Corsa al μsec 0,36°/μsec
Rotazione massima 504° (1,4 giri)
Ampiezza dell’impulso 3-5V
Larghezza banda morta 1 μsec
Lunghezza filo 300 mm (11,81″)
Calibro filo 22AWG
Proprietà intellettuale brevettata
Tipo di connettore Connettore servo TJC8 a 3 poli [MH-FC]

This Shark-5 Servo Gearbox is driven by the Hitec’s flagship HSR-M9382TH brushless, titanium geared servo. This gearbox introduces a 5:1 external gear ratio in order to lessen the range while increasing the torque and precision five-fold. If this ratio doesn’t suit your needs, be sure to check out the other Servo Gearbox options.

Having the servo mounted in the gearbox isolates the load to a steel hub-shaft that is supported in a pair of ball bearings to protect the servo from any axial loads. The gearbox opens up a world of mounting possibilities given the M4 threaded holes on each side which are on the grid pattern for compatibility throughout the goBILDA® system. The hub on the top of the gearbox provides threaded holes to fasten to, but you can also opt to fasten straight to the aluminum output gear using M4 hardware and standoffs or spacers. The 8mm REX bore of the hub-shaft can drive an 8mm REX shaft or act as a wire pass-thru.

If you’re not accustomed to using a servo gearbox, it’s just like a normal servo only larger. While the range and torque might be greater than the servos you’re used to, the control signal is identical. It will simply plug into an R/C receiver, an Arduino, Raspberry Pi, or REV controller. Furthermore, since the servo hasn’t been modified in any way, it is FTC legal!

This Servo Gearbox is available in both feedback mode, and continuous mode. In feedback mode, your signal controls the position. In continuous mode, your signal controls the speed and direction. Regardless of which you purchase, it can always be toggled to the other mode with a DPC-11 servo programmer.

Benvenuto. Iscriviti alla nostra newsletter. Subito il 10% di sconto.

Potrai rimuovere la tua iscrizione in qualunque momento.

Controlla la tua posta, riceverai un codice sconto. Ricordati di verificare nello spam. Se non ricevi il codice entro 24 ore contattaci.